Home > Multi-Rotor Frames > Phoenix Flight Gear Frames
Phoenix Flight Gear Blade 350Qx/Qx3 CarbonSpider Foldable 378mm Quad Frame
Phoenix Flight Gear Blade 350Qx/Qx3 CarbonSpider Foldable 378mm Quad Frame

Phoenix Flight Gear Blade 350Qx/Qx3 CarbonSpider Foldable 378mm Quad Frame

Item Id: PFG-BLADE350F
Your Price:
$125.00
Availability:
In Stock Now Shipping
Free Shipping
Quantity
Email a friend Email a friend
Description
Phoenix Flight Gear Blade 350QX / 350QX3 CarbonSpider

**Works with both BLADE 350QX/3 frames!**

Foldable 378mm Quad Frame



**All Electronics, Gimbal and GoPro 3 not included**



**All Electronics, Gimbal and GoPro 3 not included**





**All Electronics, Gimbal and GoPro 3 not included**












Description:

This frame designed for FPV flight and great transportability without sacrificing performance or agility. The two frame plates that for the body of the frame are made out of solid 1.5mm carbon fiber that has a 3k twill weave and a high gloss finish. Arms are also cut from the same solid carbon fiber in 3mm to keep down frame weight and provide a easily replaced arm in case of a crash. The solid carbon fiber frame keeps the frame strong and light weight, with the high gloss finish you will be the envy of your friends at the flight field.

Use of the single piece arms makes for a much simpler build not requiring all of the additional hardware and pieces associated with motor mount plates and multi piece arms. In the even of a damaged arm, two screws hold the arm to the frame, four screws hold your motor, remove them swap the arm with a spare (sold separately) and get back in the air, not back to the workbench.

The CarbonSpyder 350QX FPV Quad has been designed and outfitted with a variety of build types. Intended to satisfy the growing hobby of multi rotor flight and arial photography, this quad is simple to build and fly for the beginner who is looking for a economical entry to multirotors. With consideration to developing your skills, you can upgrade, tune and customize the CarbonSpyder 350QX to your liking. Upgrade with high efficiency motors, propellers, FPV equipment and gimbals or, the addition of flight controller accessories as you hone your skills. The frame has been designed to be easy to build with minimal hardware and a simple layout.

Balancing your drone is crucial for quality flight. The CarbonSpyder 350QX is easy to balance, even with all the FPV gear you need attached. Several build configurations allow you to use this quad as a sport/leisure craft, several camera mounting options also allows you to film your fight. If you want to fly FPV then you are able to mount your camera on the included board camera mounting plate. A top mounted accessory plate help to secure and protect your FPV video downlink and battery. Should you want to take some stabilized footage we have included mounting for the BLADE 350Qx pro Gimbal.

Instructions:
1. Install the arms with M3x10 screws inserted through the arm tabs, then bottom plate and finally the arm. Thread on a 3x30mm aluminum standoff to secure. Repeat for all four arms. We recommend using a low strength Loctite on all aluminum standoffs.

2. Install the landing gear M3x30 nylon standoff with a M3x8 screw through the landing gear hole on all four arms.

3. Install the last four nylon M3x30 standoffs with M3x3 spacers at the locations noted on the diagram.

4. Install your Blade 350QX electronics, the flight controller mounts over the FC location with adhesive foam holding in place. The GPS antenna should mount to the top of the top plate with the GPS receiver mounted to the underside of the top plate. The motors and ESC’s will mount to the arms. We recommend covering the ESC’s with heat shrink tubing and securing them to the arms with some servo tape and a velcro strap. The orientation LED’s can be mounted to the ends of each arm and tied in place with some fish line.

5. If you are mounting any accessory or gimbal plates install them onto the top plate now. Install the top frame plate to the assembled lower half with M3x6 screws.

Weight
w/Hardware 193g

Included:

1 - CarbonSpyder 330 FPV Quad Frame top plate
1 - CarbonSpyder 330 FPV Quad Frame bottom plate
4 - CarbonSpyder 330 arm tab
1 - CarbonSpyder 330 Board Cam Plate
1 - CarbonSpyder 330 Board FPV Cam Plate
1 - Board Cam Tab
12 - M3x6 screws
12 - M3x10 screws
4 - M3x8 screws
12 - M3x30 aluminum standoffs
4 - M3x3 nylon spacers
4 - Velcro straps
Adhesive foam
Fish line

Required tools:
2mm allen wrench

Optional Landing Gear (Large Long style)




Manufactured by Phoenix Flight Gear
"Created and manufactured by pilots for pilots"
Browse Similar Items