Phoenix Flight Gear Carbon Fiber 200QX
Heavy Duty (HD) Mini-H Frame
Ultra Durable 2mm Frame Upgrade

Ultra Durable 2mm Frame Upgrade (Pic Below)
**FRAME ONLY, Electronics/Stock 200QX sold separately**
**Board Camera Mount and Accessory Top Plate sold separately**
Take
your 200QX and shave grams off the weight of your stock frame. This new
2.0mm 3k twill weave solid carbon fiber frame we designed here after
there was a call from the sport flyers for an even stronger frame. With
the release of the flip capable firmware those of us who want to really
start advanced acro maneuvers are going to be pushing the QX to new
limits. We have made this heavy duty solid 2.0mm carbon fiber frame to
be lighter, faster, fly longer and remove the restrictive battery
compartment. We kept the frame within the same footprint as the stock
frame to utilize any cases that are available for the stock 200QX. This
will fit into any of those cases with little to no modification to the
case foam. These mods allow you to take your 200QX to the next level.
Durability
was a crucial component of the frame design. After experiencing tragic
failure of the stock 200QX frame on a very early flight we first wanted
to get more aggressive in our flights and the stock frame just didn’t
seem up to the task. The motors mount to the carbon fiber one piece
frame with just a motor spacer and M7 jam nut to keep weight down.
Mounting points on the arms allow for three types of landing gear. The
included standoff landing gear or RcLogger Xtreme EyeOne landing gear,
both the 38mm and 79mm landing legs will work.
Lightening of the
frame was easy, single piece construction with minimal hardware and
material removed from the central frame for improved airflow on your
4-in-1 ESC board. Reducing the overall wind profile of the craft is
another great benefit of this frame, providing faster forward flight
less affected by crosswinds. Airflow improvements have greatly helped in
our high stress acro flights of the 200QX and turn a stock mini quad
into the high performance CarbonFiber 200QX HD Mini H.
Longer
flights have also been made possible through the elimination of the
battery compartment allowing for the installation of any 800-1500 2 cell
batteries with a JST connector. Battery consumption is much lower with
all of the bulky plastic frame gone, less motor power is required to
perform arial maneuvers reducing current draw on the FET’s. With the the
stock canopy frame removed we found that the ESC board runs around 50
degrees cooler, even during high current draw sport flight.
For
FPV or aerial photography buffs out there we have made a board cam
mounting plate. Screw on the top mount accessory plate and mount your
VTX up top or, use the platform off the back of the frame to mount your
electronics. With the drastic weight reduction over the stock frame
adding some lightweight FPV gear won’t overload your quad. If you want
to film your flight many of the action cameras available will mount
right under the nose and the slots in the central frame will allow for
many mounting tie points. We mounted our Mobius under and were able to
film prop free video.
For the transplanting process the 200QX is
hands down the easiest conversion that we have come up with to date. The
200QX frame splits apart and all of the internal electronics are held
and mounted with 8 #0 phillips screws and the motors have just a acorn
nut holding them in place. No soldering, lengthening of motor wires or
advanced skill is needed, the entire process takes 30-45 minuets to
complete.
This update to our original 200QX frame has a couple
improvements to the durability of the frame, cut from 2.0mm carbon fiber
improves the rigidity of the whole frame, keyed holes for the stock
motors to mount in and, multiple motor mounting options. Spacing on the
motor holes will accommodate a variety of motors that mount on 12-14mm
spacing.
Includes:2.0mm Carbon Fiber 200QX Mini-H Frame
4 - M3x6 screws
4 - M3x40 nylon landing leg standoffs
4 - M1.4x4 self tapping screws
4 - M7 jam nuts
4 - Motor spacers
Adhesive Foam
Adhesive Velcro
Fish Line
Velcro strap
Requires:
2.0mm allen wrench
1.3mm allen wrench
#0 Phillips head screwdriver
4mm Nut driver
Specs:200QX HD frame only: 22.5g
Included 40mm legs: 5.5g
FPV cam, plate, tab with hardware 5g
Accessory plate with hardware: 8g
**We do not ship all items International so we have our checkout setup to not allow International orders.**
We do ship frames/accessories International.
Please send us a link to the exact items you would like to purchase and we will send a Paypal invoice.
We can ship up to 4 micro frames USPS Priority International for $24

Manufactured by Phoenix Flight Gear
"Created and manufactured by pilots for pilots"