Phoenix Flight Gear Carbon Fiber 200QX Mini-H Frame
Ultra Light and Durable Frame Upgrade

**FRAME ONLY, Electronics/Stock 200QX sold separately**
**Board Camera Mount and Accessory Top Plate sold separately**
Take
your 200QX and shave grams off the weight of your stock frame. This
new 3k twill weave solid carbon fiber frame we designed here after the
boss took his new 200QX out for it’s third flight and busted the motor
pod right off. After a few prototype frames we have made this solid
frame to be lighter, faster, fly longer and remove the restrictive
battery compartment. We kept the frame within the same footprint as the
stock frame to utilize any cases that are available for the stock 200QX
This will fit into any of those cases with little to no modification to
the case foam.These mods allow you to take your 200QX to the next level.
Durability
was a crucial component of the frame design. After experiencing tragic
failure of the stock 200QX frame on a very early flight we first wanted
to get more aggressive in our flights and the stock frame just didn’t
seem up to the task. The motors mount to the one piece frame with the
stock acorn nut and a woven carbon fiber spacer to keep weight down and
keep that clean carbon fiber look. Mounting points on the arms allow for
three types of landing gear. The included standoff landing gear or
RcLogger Xtreme EyeOne landing gear, both the 38mm and 79mm landing
legs will work.
Lightening
of the frame was easy, single piece construction with minimal hardware
and material removed from the central frame for improved airflow on your
4-in-1 ESC board. Reducing the overall wind profile of the craft is
another great benefit of this frame, providing faster forward flight
less affected by crosswinds. Airflow improvements have greatly helped in
our high stress acro flights of the CarbonGear 200QX Frame and turn a
stock mini quad into the high performance CarbonGear 200QX.
Longer
flights have also been made possible through the elimination of the
battery compartment allowing for the installation of any 800-1500 2
cell batteries with a JST connector. Battery consumption is much lower
with all of the bulky plastic frame gone, less motor power is required
to perform arial maneuvers reducing current draw on the FET’s. With the
the stock canopy frame removed we found that the ESC board runs around
50 degrees cooler, even during high current draw sport flight.
For
FPV or aerial photography buffs out there we have included the board
cam mounting plate. Screw on the top mount accessory plate and mount
your VTX up top or, use the platform off the back of the frame to mount
your electronics. With the drastic weight reduction over the stock frame
adding some lightweight FPV gear won’t overload your quad. If you want
to film your flight many of the action cameras available will mount
right under the nose and the slots in the central frame will allow for
many mounting tie points. We mounted our Mobius under and were able to
film prop free video.
For
the transplanting process the 200QX is hands down the easiest
conversion that we have come up with to date. The 200QX frame splits
apart and all of the internal electronics are held and mounted with 8 #0
phillips screws and the motors have just a acorn nut holding them in
place. No soldering, lengthening of motor wires or advanced skill is
needed, the entire process takes 30-45 minuets to complete.
Specs:200QX frame only: 19gIncluded 40mm legs: 5.5g
FPV cam, plate, tab with hardware 5g
Accessory plate with hardware: 8g
Includes: Phoenix Flight Gear Carbon Fiber 200QX Mini-H Frame
4 - M3x6 screws
4 - M3x40 nylon landing leg standoffs
4 - M1.4x4 self tapping screws
4 - Motor mount spacers
Adhesive Foam
Adhesive Velcro
Fish Line
Velcro strap
Requires:
2.0mm allen wrench
1.3mm allen wrench
#0 Phillips head screwdriver
4mm Nut driver
**We do not ship all items International so we have our checkout setup to not allow International orders.**
We do ship frames/accessories International.
Please send us a link to the exact items you would like to purchase and we will send a Paypal invoice.
We can ship up to 4 micro frames USPS Priority International for $24

Manufactured by Phoenix Flight Gear
"Created and manufactured by pilots for pilots"