Phoenix Flight Gear Custom Built 110mm Micro-H 8.5mm
Motor Scisky Copter Bind-n-Fly Extreme Edition
For this Extreme Edition we direct solder a JST to the FC
That's the only way to run 8mm motors
For smoothest throttle response do not upgrade to the dark Edition.
They are for "Balls to the Wall" sport flying and might not be the
best choice for FPV racing unless it is a large course.
**PHOTOS BELOW WIL BE UPDATED WITH NEW SCISKY FLIGHT CONTROL PIC**
**3D parts shown below are optional**
The
micro frame market has taken off with a revolution in flight
controllers and a variety of coreless motors. This super light racing
frame has a second top plate that secures your micro motors the top and
bottom the motors strengthening the frame. Securing the motors with two
points also makes this the most rigid frame that we have to offer to
date. Build able with either 7 or 8mm motors you will be able to upgrade
and reconfigure as your skills improve. With minimal nylon hardware and
foam motor mounting we keep this frame light and easy to assemble.
For
the racer in you, the top plate can be shifted forward with 7mm motors
installed for face paced racing. Another reason we chose a two plate
frame was to strengthen the frame to make it more rigid. To protect
your flight controller we have also made two optional flight controller
yards, one for the AlienWii and one for the blade NanoQX and Hubsan X4.
If you are flying FPV we also have mounting place for an antenna
protector post for the Spectrum VA1100. There is also a ledge for
mounting the VA1100 and micro pico cameras on the front.
Specs:
Size: 113mm
Weight frame only: 3.5grams
CL-0820-15 Hyper Speed Coreless Motor 8.5x20mm

To fit these motors into your Alias, you will have cut off and use the plugs from your old motors.
Performance data:
- operating voltage: 1.5-3.7V
- max. thrust: 40g (direct drive, Hubsan X4 propeller)
- 2.75A max. load current at 3.7V (Hubsan X4 propeller)
- factory lifetime rating: 5-6 hours
Dimensions:
- can diameter: 8.5mm
- can length: 20mm
- shaft diameter: 1mm
- shaft length: 5mm
- weight: 4.9g
All motor packs contain equal amounts of clockwise and counter
clockwise motors. To maximise performance and life span, dont run them
in reverse!
Motor rotation and correct polarity is indicated by the wire color:
clockwise: red +, blue -
counter clockwise: white +, black
Hubsan Rotor for H107L Black & White - Props
Hubsan X4 H107 Propeller Blades Props Rotor Set Factory Units H107L H107D H107C
Includes:2 Black Propellers
2 White Propellers
Quanum Pico Micro Scisky 32bit Brushed Flight
Control Board w/Motor Plugs+Battery Connector
**Comes with Motor Plugs+Battery Connector Pre-Soldered**
Same Motor plug as our MMW Chaoli Motors
Please choose Hubsan style or JST battery connector from dropdown
box and we will solder your connector before shipping
Good things do come in small packages and in this case its not just good, its great.
Setting the standard in Multi-Rotors once again, Quanum has listened
to builders of mini and micro quadcopters and released the a full
function Brushed Flight Control Board which was purpose designed and
built for quads around the 100mm and sub 100mm class.
This brushed FC has four built in ESC's
at 4.3A per FET and is ideal for brushed motors in the 6~8mm size
range. It also has a built in DSM2/DSMX compatible receiver.
The Pico is a full 32bit Cleanflight supported FC board and has a
micro USB connection. Once you have downloaded cleanflight on your PC,
you simply plug in your Pico Quanum FC Board into your PC and you have
complete control over its settings. Its that easy.
NOTE: DO NOT PLUG THE BATTERY AND USB IN AT THE SAME TIME, THE RX WILL RECIVE POWER FROM THE USB FOR SET UP. THE FETS WILL BE DAMAGED OTHERWISE.
Specs:
ESC: Brushed 4.3A x 4 (2~32KHz 4KHz stock) 6,7,8mm motors compatible
RF: DSM2/DSMX compatible
Size: 20x33x6mm
Weight: 2.5g
Software: Cleanflight or Baseflight compatible
Voltage: 1s compatable, with built in 5V DC/DC converter
Recommended battery 500mAh-750mAh
Required for flight: Spektrum Transmitter
Included:
Top Frame Plate
Bottom Frame Plate
2 - M3x15 nylon standoffs
4 - M3x6 nylon screws
4 - CL-0720-12 - coreless motor set, 7x20mm (2 CCW - 2 CW)
4 - Props HUBSAN Rotor for H107L 2Black & 2White
1 - BLADE 4-in-1 Flight Control Unit Rx/ESCs/Gyro (Nano QX FPV style)
Adhesive velcro
Adhesive foam 3M tape
Fish line
**Micro Motor Tips**
1-Drill props with #62 drill bit so they press on all the way.
2-Rest motor bottom end cap on corner of a table or something to keep it from popping off when you push the props on.
3-Add a little epoxy to the edges of the bottom end caps to keep them from popping off in a crash or when pushing props on.
4-Let motors cool a little in between battery packs.
5-Replace nicked or damaged props as damaged props will cause the motor to run hotter and will affect efficiency.
6-Make sure micro is balanced as an unbalanced micro will not fly as well and motors will run hotter and will affect efficiency.
7-Buy spares because if you crash a lot you will need them.
Manufactured by Phoenix Flight Gear
"Created and manufactured by pilots for pilots"