Homeá>áMICRO Kits/Frames & Accessoriesá>áReady / Bind N Fly MICRO Kitsá>áScisky
Phoenix Flight Gear Custom Built 90mm Micro-X Enclosed Prop 8.5mm Motor Scisky Copter Bind-n-Fly

Phoenix Flight Gear Custom Built 90mm Micro-X Enclosed Prop 8.5mm Motor Scisky Copter Bind-n-Fly

Item Id: PFG-90MXPG-8BNF-2
Your Price:
$170.00
Availability:
In Stock Now Shipping
Free Shipping
Choose Options
Micro Transmitter + Labeling & Setup
Quantity
Email a friend Email a friend
Description
Phoenix Flight Gear Custom Built

90mm Micro-X Enclosed Prop

8.5mm Motor Scisky Copter Bind-n-Fly



**This micro copter comes Custom built just Bind N Fly**

Just add TX from dropdown box to make a Ready To Fly, Will bind to ANY SPEKTRUM Transmitter


**We Solder on a JST style connector so larger batteries can be used**


**PHOTOS WILL BE UPDATED with SCISKY FC BOARD SOON**









Quanum Pico Micro Scisky 32bit Brushed Flight


Control Board w/Motor Plugs+Battery Connector



**Comes with Motor Plugs+Battery Connector Pre-Soldered**
Same Motor plug as our MMW Chaoli Motors


Please choose Hubsan style or JST battery connector from dropdown

box and we will solder your connector before shipping




Good things do come in small packages and in this case its not just good, its great.

Setting the standard in Multi-Rotors once again, Quanum has listened to builders of mini and micro quadcopters and released the a full function Brushed Flight Control Board which was purpose designed and built for quads around the 100mm and sub 100mm class.

This brushed FC has four built in ESC's at 4.3A per FET and is ideal for brushed motors in the 6~8mm size range.  It also has a built in DSM2/DSMX compatible receiver.

 The Pico is a full 32bit Cleanflight supported FC board and has a micro USB connection.  Once you have downloaded cleanflight on your PC, you simply plug in your Pico Quanum FC Board into your PC and you have complete control over its settings.  Its that easy.

NOTE: DO NOT PLUG THE BATTERY AND USB IN AT THE SAME TIME, THE RX WILL RECIVE POWER FROM THE USB FOR SET UP. THE FETS WILL BE DAMAGED OTHERWISE.

Specs:
ESC: Brushed 4.3A x 4 (2~32KHz 4KHz stock) 6,7,8mm motors compatible
RF: DSM2/DSMX compatible
Size: 20x33x6mm
Weight: 2.5g
Software: Cleanflight or Baseflight compatible
Voltage: 1s compatable, with built in 5V DC/DC converter

Perfect for FPV micro setups.


CL-0820-15 Hyper Speed Coreless Motor 8.5x20mm







Motors come with Micro JST-1.25 plugs Installed.
This is the same connector that is on the Nano QX and AlienWii boards so motors will plug right in.

Performance data:

  • operating voltage: 1.5-3.7V
  • max. thrust: 40g (direct drive, Hubsan X4 propeller)
  • 2.75A max. load current at 3.7V  (Hubsan X4 propeller)
  • factory lifetime rating: 5-6 hours

Dimensions:

  • can diameter: 8.5mm
  • can length: 20mm
  • shaft diameter: 1mm
  • shaft length: 5mm
  • weight: 4.9g 

All motor packs contain equal amounts of clockwise and counter clockwise motors. To maximise performance and life span, dont run them in reverse! 

Motor rotation and correct polarity is indicated by the wire color:
clockwise: red +, blue -
counter clockwise: white +, black -

**Micro Motor Tips**

1-Drill props with #62 drill bit so they press on all the way.
2-Rest motor bottom end cap on corner of a table or something to keep it from popping off when you push the props on.
3-Add a little epoxy to the edges of the bottom end caps to keep them from popping off in a crash or when pushing props on.
4-Let motors cool a little in between battery packs.
5-Replace nicked or damaged props as damaged props will cause the motor to run hotter and will affect efficiency.
6-Make sure micro is balanced as an unbalanced micro will not fly as well and motors will run hotter and will affect efficiency.
7-Buy spares because if you crash a lot you will need them.



Hubsan Rotor for H107L Black & White - Props




Hubsan X4 H107 Propeller Blades Props Rotor Set Factory Units H107L H107D H107C

Includes:
2 Black Propellers
2 White Propellers

**Micro Motor Tips**

1-Drill props with #62 drill bit so they press on all the way.
2-Rest motor bottom end cap on corner of a table or something to keep it from popping off when you push the props on.
3-Add a little epoxy to the edges of the bottom end caps to keep them from popping off in a crash or when pushing props on.
4-Let motors cool a little in between battery packs.
5-Replace nicked or damaged props as damaged props will cause the motor to run hotter and will affect efficiency.
6-Make sure micro is balanced as an unbalanced micro will not fly as well and motors will run hotter and will affect efficiency.
7-Buy spares because if you crash a lot you will need them.



Manufactured by Phoenix Flight Gear
"Created and manufactured by pilots for pilots"